Piston ring compressing tool, compresses piston rings to fit into bore. Without this tool you risk snapping piston rings, the tool also speeds up the fitting of new rings

For 57mm - 125mm bores, supplied with hex key for bore adjustment. Not suitable for CARC models

 This part is available by special order, request a quote

Cam follower / tappet, standard size

Not for PI / hydraulic tappet models produced between 2003 and 2006

 2 in stock

 17045860 GU17045860 17 04 58 60
 1704 5860 1704.5860 17.04.58.60

Complete gasket kit

This is only a gasket set, it does not include oil seals and O rings. The top end O rings required are 12x ENA97624 and 2 x ENA90203

 1 in stock

30999060-z 30999060 GU30999060 30 99 90 60
 3099 9060 3099.9060 30.99.90.60

Complete gasket kit for all square barrel 1000 models

This is only a gasket set, it does not include oil seals and O rings. The top end O rings required are 12x ENA97624 and 2 x ENA90203

 This part is due back in stock soon, call 01484 841395 to reserve yours

29999000-z 29999000 GU29999000 29 99 90 00
 2999 9000 2999.9000 29.99.90.00

Stainless steel braided hose oil lines for heads on square barrel models. See ENA14662 if you also need threaded link to cylinder head

Always replace crush washers (SIA12200 x 2 and SIA10900 x 2) when replacing oil lines, you may also require our banjo bolt ENA95990. Also known as Guzzi ref. 01153600 and 01153602

 3 in stock

 14153660 GU14153660 14 15 36 60
 1415 3660 1415.3660 14.15.36.60

Pair of chrome tubular rocker cover protector bars for round and square barrel engines, these will protect barrels and rocker cover in the unfortunate event of your bike being dropped

These head protectors bolt to the head using existing rocker cover bolts, they won't fit models with fairing lowers that wrap around the cylinders (e.g. Spada) without modification. To modify simply reduce the length of the rear section of the bar to stop short of the fairing and insert the supplied grommet. These bars are supplied with a plastic grommet for each end, this will need chamfering or leaving off on round head models with bolt on rocker cover breather pipes, e.g. T3. These bars will not fit on a T3 or other model with knee pads

 This part is due back in stock soon, call 01484 841395 to reserve yours

Uprated double row cam chain, ideally fit with sprung chain tensioner ENA20071

 This part is due back in stock soon, call 01484 841395 to reserve yours

 28058060 GU28058060 28 05 80 60
 2805 8060 2805.8060 28.05.80.60

Pair of chrome tubular rocker cover protector bars for square barrel engines, these will protect barrels and rocker cover in the unfortunate event of your bike being dropped

These head protectors bolt to the head using existing rocker cover bolts, they won't fit models with fairing lowers that wrap around the cylinders (e.g. Spada) without modification. To modify simply reduce the length of the rear section of the bar to stop short of the fairing and insert the supplied grommet.

 This part is available by special order, request a quote

Polished aluminium distributor cover for models with points or electronic ignition. Alternative for plastic cover ENA14420

See SSA05025 for the screws which secure this dizzie cap

 This part is due back in stock soon, call 01484 841395 to reserve yours

14715420-z 14715420 GU14715420 14 71 54 20
 1471 5420 1471.5420 14.71.54.20

Long screw in polished alloy dipstick with O ring for models with fairing lowers (dipstick protrudes through fairing to make oil level checking much simpler and more accurate)

Use this longer dipstick for models fitted with a sump extension, note that the dipstick extension is 80mm long which is shorter than the original part. Supplied with both O rings

 This part is available by special order, request a quote